Country Living
Country Living, Country Skills
Country People - A Country Living Resource and Community
Message Board
Country Topics
Trading Post
Memory Lane
Country Skills
Country Cooking

The Kitchen

Photo Gallery
Vintage Photos
Special Collections

Country Humor
Country Sounds
Coloring Book
Interactive Story

Farm Tractors
Tractor Parts
Tractor Manuals

Classic Trucks
Antique Tractors
Modern Tractors
Site Map
Links Page
Contact Us

Country Discussion Topics
To add your comments to this topic, click on one of the 'Reply' links below.

Maytag washing machine schematic
[Return to Topics]

UncleTom    Posted 02-19-2005 at 16:52:10       [Reply]  [No Email]
I am looking for a web site that has a schematic of the wiring diagrham for a maytag washing machine m#LAT2500AAE. I had a sewer backup while the machine was running. I shut the machine off so the basement wouldnt flood until i unpluged the drain. The machine is dead. It has power. The door lid switch reads ok. Thanks in advance. UncleTom

Burrhead    Posted 02-19-2005 at 18:04:29       [Reply]  [No Email]

toolman    Posted 02-19-2005 at 20:53:53       [Reply]  [No Email]
thats a good site burr , but they are a little slow, i contacted them nearly a year ago to come fix the wifes dishwasher still waiting and i can,t find a thing on repairing it in the chevy truck repair manual.

Burrhead    Posted 02-19-2005 at 21:15:46       [Reply]  [No Email]
I fixed a dishwasher using them folks directions. Dunno if all their info is that good or not but that was right on line.

toolman    Posted 02-19-2005 at 21:29:38       [Reply]  [No Email]
ya they help good i gotta change the motor in mine and just can,t figure how to fit that engine stand under the machine.

toolman    Posted 02-19-2005 at 17:46:55       [Reply]  [No Email]
did you check your breaker, if it is a gfi it may have tripped, always look for the simple things first and work up to the more complicated ones, good luck.

john ladd    Posted 02-19-2005 at 17:30:37       [Reply]  [Send Email]
did you check the fuse that is right behind the lid switch.if this is blowed it will not work this is a 10 amp 250 volt fuse can get at radio schak..john

Gerrit    Posted 02-19-2005 at 17:11:38       [Reply]  [No Email]
Try this:

bo    Posted 02-19-2005 at 17:18:17       [Reply]  [No Email]
A schematic won't help you...the control is on top and all you have are wires going to the motor...this is the main unit. Does it hum? If it does, it's seized and you could free it up by twisting the armature by'll need to get to it. You also have a water in pump and a water out pump...those would be impacted and the in water pump would be the first one to be impacted...that's just a selonoid with one electrical contact that can be cleaned up.

Put it into the wash cycle and listen for a hum out of the's still water soaked and I'd first put a heater blower on it to dry it heater or a hair dryer. Frankly...all you have is a motor and two selonoids to let the water in and out.

UncleTom    Posted 02-19-2005 at 17:33:05       [Reply]  [No Email]
You guys are awsome. Garrit,that diaghram is exactly the one i need. Now if i can just read it. Bo, it doesnt hum. It is totaly dead. I am suspecting the lid switch yet. It has a 4 prong plug on the switch. The 2 marked motor, machine will read continuity when you open and close the switch. The other 2 marked nuet and line are open no mater what postition the switch is in. Not sure if that is correct or not. Uncle Tom

Frank    Posted 04-07-2009 at 07:54:22       [Reply]  [Send Email]
I need to get my Maytag - Model No. MAV7000AWW open to try to fix it. I believe the belt keeps loosening. We bought it "USED" about a month ago, and before they dilivered it we wanted to see it work. It made a wobling sound and they said the belt just needed to be tightend. So, how would I go about doing that? I've replaced belts on dryers and replaced motors on washers before, and they all have different ways to open them. Could you please let me know what the easiest and most efficient way to get this done?
Thank you in advance.

UncleTom    Posted 02-19-2005 at 17:53:27       [Reply]  [No Email]
I have checked the breaker and is ok. I have power to the outlet that it is plugged into. I have even tried a different outlet.

UncleTom    Posted 02-20-2005 at 08:58:32       [Reply]  [No Email]
Thanks for all your help. In the end it was the lid switch that was bad. It didnt make sense the way it read on the meter. Will have to pick one up. Thanks all. UncleTom

[Return to Topics]

[Home] [Search]

Copyright © 1999-2013
All Rights Reserved
A Country Living Resource and Community